Portable Sand Blasting Machine in Jodhpur

Manual operation is required for portable sand blasting equipment. The portable abrasive blaster is a low-risk method of system delineation that may be employed with a wide variety of abrasive media. Descaling, shot peening, deburring, deflashing, polishing, cleaning, and stress relief are all features of this machine. The thickness of the sheet used to construct the sand blasting machine's body should not be less than 6mm. Sand blasting equipment is tested in hydraulic machines at a pressure of 20 kg/cm2. For both the inner and exterior surfaces of portable sand blasting machines, mild steel is used. After embedding the material or abrasive media, a mushroom valve is used to connect the vacuum pack. NRVs (non-return valves) are used to prevent air passing through a filter from flowing back. Between the pressure gauge and the air filter regulator is where the NRV is located. At the very least, a pressure of at least 7kg is necessary for optimal operation of the shot blasting machine, which is adjustable by the user. Sand blasting machine P7-1000 has a 460-kilogram sand storage capacity.

A filter regulator is used in a portable sand blasting hopper to supply dry, clean air at an 80 PSI pressure. A pinch valve is used to regulate the flow of blasting media such as steel shots, sand, and abrasive garnet used in sandblasting. The mixing tube is linked to the pinch valve (how much quantity to mix is controlled by the user). The mixing tube contains two openings; one for air and one for abrasive material. The abrasive hole is attached to the blasting hose, which is already connected to the nozzle holder, which will receive a 95mm sand blasting nozzle. A pinch valve rubber sleeve is used to protect the valve from further damage caused by the blasting process.

A ball valve is utilised to allow air into and out of the sand blasting hopper. The usual length of the blast hose is ten metres, however it may be expanded to meet customer requirements. The diameter of the sandblasting nozzle is 9.5mm.

The portable sand blasting equipment has a total height of 1611mm. The machine's body measures 761mm in diameter. There is one main hole plate on a portable shot blasting machine that is used for maintenance and cleaning the inner part of the machine. Because material is embedded for blasting in the upper part of the machine, there is a counterfeit from which blasting media is separated from large particles. Otherwise, large particles will clog the nozzle.

The area covered by the surface cleaning is 15-21 Sq. Mtrs./Hr. A 1.25-inch connection valve is used to connect the components. The tee connector is used to link the NRV, the air that enters the machine to produce a vacuum and pushes the mushroom valve upward to prevent any further air from entering, and the air that enters the mixing tube to generate pressure for blasting. Additionally, the tee connector is 1.25. The release/exhaust valve is used to vent the air that was sucked into the machine to produce the vacuum.

There are two types of portable sand blasting machines. One is remote-controlled, while the other is not. It is split into four categories: 

• P7-1000
• P7-500
• P7-300
• P7-150 

Uses of portable sand blasting machine

• Portable sand blasting machine helps to preserve the use and endurance of your metal pipes and possession made by metals and fittings.
• It helps to reanimate the material and make it look new again.
• It allows you to retrieve corners and areas that are difficult to reach.
• It helps to fix the surface for consecutive stoning and polishing.
• It conserves time and is more efficient than sandpaper.
• This procedure does not make use of complex machinery.
• The dominant effort of sand blasting removes trash even from tough surfaces like concrete.

Application of Portable Sand Blasting Machine

• It aids in the stabilisation of the surface before subsequent stoning and polishing.
• It is more time efficient and effective than sandpaper.
• This method does not need the use of sophisticated machinery.
• Sand blasting's dominating effort effectively eliminates debris from even the most difficult surfaces, such as concrete.

Portable Sand Blasting Machine Price in Jodhpur

Sand blasting machines are used in a variety of applications, including rail coaches, axles, handicrafts, wooden, steel pipes, tanks, heat exchangers, stones, marble, granite, transformers, military, ships, bridges, dam gates, turbines and blades, and vehicle bodies, cars, and buses. Sand Blasting Hopper is India's most straightforward manufacturer of mobile, macro, compact, and portable sand blasting equipment. Portable Sand Blasting Machines Manufacturers include two input lines from which air or sand is drawn into the blending unit, this combination then travels to an output channel via sand blasting nozzle to supply an influence stream.

Portable Sand Blasting Manufacturers in Jodhpur

Portable sand blasting machines and equipment is available for sale in Jodhpur at a reasonable price and of the highest quality. In Jodhpur, Rajasthan, India, we are the leading Portable Sand Blasting Machine Manufacturer, supplier, and exporter of portable sandblasting machines, shot blasting machines, grit blasting machines, shot blasting cabinets, pressure blasting cabinets, thermal spray guns, arc spray guns, metalizing guns, and abrasive blasting media. The Portable sand blasting machine P7-1000 has the lowest price of any other impermanent. Client satisfaction is our goal, which includes timely shipping, the lowest possible pricing for the equipment, and timely machine service.

Get in touch with us to know more.